Hearing Rehabilitation for Acoustic Neuroma Patients

Post Reply
Posts: 21
Joined: Tue Apr 12, 2016 8:52 am
Country: USA
Gender: female
Year of birth: 1955
Location: California

Hearing Rehabilitation for Acoustic Neuroma Patients

Post by Subri » Sun Jun 12, 2016 1:40 pm

Here is a comprehensive article that may be helpful:
In the modern era of acoustic neuroma treatment, numerous hurdles have been
cleared. In the early part of the 20th century, patients were at high risk of death
from either the surgical treatment of these tumors or from the tumors themselves.
After reducing the risk of death or mortality to <1%, the next goal was to avoid
neurovascular injuries that could cause strokes or other significant morbidities,
including facial palsy. Subsequently, research and increased expertise have
improved the preservation of the facial nerve. In large volume centers, preservation
of facial nerve function at normal or near normal levels is in the 90%+ range,
depending on the size of tumor and treatment paradigm chosen (whether radiation
or surgery).

One of the last great obstacles in the management of acoustic neuromas is hearing
preservation and/or rehabilitation after hearing loss. Hearing loss is the most
common disability in patients with acoustic neuromas and affects all age groups.
Hearing loss is a symptom that affects one’s quality of life, whether one chooses
observation or monitoring of a tumor with frequent (serial) MRI scans, radiation
therapy, or microsurgical excision. It can vary from no or mild hearing loss to
complete deafness (also known as profound hearing loss or single-sided deafness –

Hearing loss can disrupt one’s social and vocational life; it can contribute to
depression and a sense of isolation. Hearing rehabilitation, through the use of
hearing aids and assistive listening devices, can enhance one’s ability to
communicate with others (by phone or in person) and significantly improves a
patient’s quality of life.
As the degree of hearing loss from an acoustic neuroma varies among patients, the
type of hearing aid best suited for each individual depends on many factors,
especially the hearing level of both the ear affected by the tumor and the unaffected
ear. Surgical removal of an acoustic neuroma can affect any remaining hearing,
possibly causing partial or complete hearing loss. Surgery does not affect the
hearing in a patient’s good ear, and most patients can still hear adequately in most
situations. However, with single-sided deafness, it can be hard to locate sounds as
well as hear in situations with much background noise.
For small tumors, it may be possible for the surgeon to preserve the hearing in the
affected ear (e.g., via a middle fossa or retrosigmoid approach). For larger tumors,
the likelihood of preserving hearing is lower. If the surgeon has been able to
preserve some hearing in the affected ear, it may be feasible to try a conventional
type of hearing aid. If the unaffected ear has some hearing loss, a conventional
hearing aid in that ear may also be helpful.
In the case of total hearing loss/deafness in one ear, called unilateral profound
hearing loss or single-sided deafness (SSD), a conventional hearing aid will not be
helpful. In the case of bilateral hearing loss, bilateral amplification is recommended
to allow better understanding in noise and allow directionality of sound. This issue
is faced by patients with bilateral acoustic neuromas, as is found in
Neurofibromatosis Type II (NF-2), which accounts for about 5% of all acoustic
neuromas. Although many options exist for both unilateral and bilateral hearing
loss in patients with acoustic neuromas, this booklet will give a concise overview of
the options available. Please discuss further with your neurotologist, or find an
audiologist near you at http://www.audiology.org. (An audiologist is a professional
who assesses and manages hearing and balance related disorders.)
There are four types of hearing impairment. First, conductive hearing loss occurs
when sound is not conducted efficiently through the outer and middle ears. It
usually involves a reduction in sound level; however, if sounds are amplified,
speech understanding and hearing clarity are preserved.
Second, sensorineural hearing loss occurs when there is damage to the inner ear
(cochlea) or nerve pathways from the inner ear to the brain. It involves a reduction
in sound level, speech understanding and hearing clarity. Acoustic neuromas
typically cause this type of hearing loss.
Third, mixed hearing loss occurs when a sensorineural hearing loss occurs in
combination with a conductive hearing loss.
Lastly, auditory processing disorders (APD) occur when auditory portions of the
brain are affected by aging, injury (trauma), dementias, tumors, or unknown causes.
These disorders can disrupt sound localization, lateralization, discrimination,
pattern recognition and the temporal aspects of sounds as well as the ability to deal
with degraded and competing acoustic signals.
A conventional hearing aid can be a good choice if some hearing is preserved in the
ear affected by the tumor. Several types and sizes of conventional hearing aids are
available. The correct type depends on many factors; cost is important because most
hearing aids are usually not covered by insurance. Although insurance companies
may pay for the cost of audiologic tests, they rarely cover the cost of hearing aids.
Other options available to qualifying patients include the Sertoma Hearing Aid
Bank which provides hearing aids for individuals 65 years and older, based on
income. To find a club near you visit http://www.sertoma.org. Also, the Lions
Club (The Lions Affordable Hearing Aid Project) provides hearing aids for lowincome
individuals. To find a club near you visit http://www.lionsclubs.org. The
patient should discuss in detail which of these options is best with an audiologist
and the treating physician, since each case is highly individualized.
Patients may have concerns about cost and appearance of conventional hearing aids.
However, these devices are used widely to help with hearing loss in patients with
and without acoustic neuromas with excellent results. Many states do offer a 30-
day return policy on the hearing aid sold; patients are expected to pay for the fitting
fee and consultation. If the patient decides to return the hearing aid within the 30-
day trial period, he/she will be refunded all of the money less a professional fee
(typically around $150 to $200).
Hearing aids can vary in cost from hundreds to thousands of dollars, depending on
size, complexity and extra features. When choosing a hearing aid, the patient should
work with a reputable facility; service and a proper fit are as important as the device
itself. Each device has benefits and limitations. It can take repeated fittings, finetuning
of the device and patience to achieve optimal results.
The measure of effectiveness varies with each individual. For instance, even if one
has poor speech discrimination (also known as the word recognition score), the
hearing aid may enhance communication in combination with visual cues (e.g.,
improved lip reading) or improve awareness of sounds in the environment for
greater safety (e.g., doorbell, car horn, police siren, fire alarm, dog barking, etc.).
Conventional hearing aids come in two basic types: analog and digital. Analog
hearing aids, the oldest type, have a microphone that picks up sound and converts
the sound into small electrical signals. These signals are then made louder, or
amplified, and sent to the speaker on the hearing aid. Programmable analog aids can
amplify quiet sounds until they are loud enough to be heard; these give less
amplification to sounds that are already loud, protecting the user against
uncomfortably loud sound levels. Analog hearing aids are simple to use and often
inexpensive. However, they have been largely replaced by aids that use digital
signal processing.

Digital aids work in a different way than analog aids. Digital hearing aids take the
signal from the microphone and convert it into 'bits' of data that can be manipulated
by a tiny microprocessor, or computer, in the hearing aid. This technology makes it
possible to finely adjust sounds to suit individual needs and different listening
conditions (e.g., quiet environments versus louder settings such as restaurants and
large group gatherings). Digital processing requires less space, which allows
manufacturers to include more programmable features in a smaller package.
Both analog and digital hearing aids vary in size (behind-the-ear, in-the-ear, in-thecanal
and completely-in-the-canal) and in circuitry features (see Table 1). The cost
of a hearing aid generally increases with a decrease in size and an increase in
advanced features.
Behind-the-ear hearing aid (BTE)
Overview: The BTE style hearing aid is housed in a small curved case which fits
behind the ear and is attached to a custom earpiece or earmold, which is molded to
the shape of your outer ear. Some BTE models do not use a custom earmold;
instead, the rubber tubing is inserted directly into the ear. The case is typically flesh
colored but can be obtained in many colorful patterns (for children) and shaded
colors (to blend in with the patient’s hair).
BTE hearing aids are also available with an “open fitting,” which is a slim tube that
goes down into the ear canal with an open dome or highly vented ear piece at the
end. This allows for a reduction in the occlusion effect (hollow or echo sounding
voice) and leads to a more natural sounding voice for the patient. They are less
noticeable than hearing aids with earmolds and are typically more appropriate for
individuals with higher pitched hearing loss; however, they may not be suitable for
severe to profound hearing losses.
Receiver-in-the-canal (RIC) hearing aids refer to BTE aids with the loudspeaker or
receiver component inserted in the ear canal instead of behind the ear. This
modification allows for a smaller hearing aid; the receiver can be housed in a
number of different ways: a dome, micro mold, or custom earmold. This style of
BTE is cosmetically appealing; however, like the open fit models, it may not be
appropriate for severe to profound losses.
 Typically, a BTE hearing aid is the most powerful hearing aid style available; it
may be the best option for persons with severe to profound hearing loss.
 Non-occluding earmolds may be used with BTE hearing aids, if a medical
condition exists that prohibits the use of in-the-ear styles, or if the patient reports
a “plugged” sensation when wearing other hearing aid styles.
 Larger battery sizes used in BTE aids may be easier to handle than smaller styles
for those with limited manual dexterity or vision deficits.
 BTE aids may be the most appropriate choice for young children, as only the
earmold needs to be replaced periodically as the child grows and the ear changes
in dimension.
 Special features such as FM, direct auditory input and directional microphone
technology are routinely available with most BTE styles and models.
 Telecoil circuitry (which allows the hearing aid to pick up magnetic signals in
telephones and assistive listening devices) is often more powerful than is seen
with in-the-ear hearing aids.
 Fit and appearance may be less acceptable to some patients, although modern
BTE designs have become smaller and less noticeable. This style is the most
susceptible to moisture damage from sweat.
Custom hearing aids
Overview: No two ear canals (the tunnel running from the outer ear to the ear drum)
are alike. Custom hearing aids provide patients with hearing technology molded to
his/her ear canal shape and size. An earmold impression is the first step in the design
phase of a custom hearing aid. An audiologist will take the mold of the patient’s ear
and help determine the most appropriate size and features for the hearing aid based
on the individuals hearing loss.
In-the-ear hearing aid (ITE)
Overview: The ITE style hearing aid fits directly into the external ear. The circuitry
is housed primarily in the concha (external) portion of the ear. ITE aids have their
working parts in a custom made shell so the whole aid fits into the ear. This style has
typically been considered to be more cosmetically appealing. (However, modern
BTE hearing aids have become smaller and are often less noticeable than some ITE
hearing aids.)
 More secure fit and easier insertion and removal than with BTEs.
 Less wind noise in the smaller styles than with BTEs.
 Directional microphone technology available for most styles.
 All components are integrated into a one-piece shell, which may be easier to
handle and operate than for BTE styles.
 Tend to need repairing more often than BTE aids.
 Some ITE aids can be seen from the side.
 Battery size in ITE aids is typically smaller than BTE aids; this may be difficult
for those with manual dexterity problems and/or visual deficits.
 This style is not as powerful as BTE hearing aids and may not be suitable for
severe to profound hearing losses.
In-the-canal (ITC) and Completely-in-the-canal (CIC) hearing aids
Overview: Due to the miniaturization of the component parts (including the
microphone, receiver and battery), it is possible to make hearing aids small enough
to fill only a portion of the concha (ITC) or fit deeply into the ear canal (CIC).
Along with ITE aids, these styles have characteristically been considered to be more
modern and cosmetically appealing.
 Improved cosmetic benefits due to smaller styles; the smallest ITC and CIC aids
fit right inside or deep in the ear canal and cannot usually be seen.
 Less wind noise than with BTEs.
 Deep microphone and receiver placement with CICs may result in increased
battery life (e.g., reduced power consumption) and high frequency amplification
compared with other styles.
 Directional microphone technology available for most ITC styles.
 Some people find them easier to put in and take out than BTE styles.
 If a patient has severe hearing loss or small ear canals, this type of aid may not
suit him/her.
 These aids tend to need cleaning and repairing more often than BTE aids;
slightly less durable than BTE aids.
 Very small models, though less noticeable, may be more difficult to operate,
particularly for patients with dexterity or vision problems.
 They may not be compatible with assistive listening devices such as a loop
system. (A loop helps one hear sound from a television, stereo, or radio. A loop
may be set up with a microphone to help hear conversations in noisy places or
a show in a theater.)
 Directional microphone technology is not generally available for CICs.
 Some limitations with fitting range for severe to profound hearing losses.
Table 1: Conventional Hearing Aids: Styles, Benefits, Limitations
Type of Aid Benefits Limitations

 Fits a wide range of losses
 More room for advanced
 Appropriate option for severe
to profound hearing loss
 More opportunities for nonoccluding
earmolds which
provide more natural sound
 Often more durable
 Larger batteries offer longer
 More flexibility with
changing hearing losses
 Appropriate for all ages
 May be large in size
 May be more noticeable than
smaller styles, depending on
hairstyle, etc.
 Susceptible to moisture
damage from sweat

 Microphone is located in the
ear, offering better
 Comfortable, custom fit
 Large enough for user
controls (volume, etc.)
 Cosmetics
 Decreased wind noise
 Feedback is more likely than
with a BTE
 Slightly less durable than BTE
 More maintenance and
cleaning required
 Limited advanced features
(depending on size)
 Not suitable for severe to
profound losses
 Shorter battery life
 May not be compatible with
direct audio input systems
(e.g., loop systems)
 May not offer telecoil
 Increased occlusion without
deep insertion depth
If a conventional hearing aid is not feasible, such as in unilateral deafness, then
other types of specialized hearing devices are available. These options include the
CROS (contralateral routing of signal) and BiCROS aids, referring to whether one
(CROS) or both ears (BiCROS) have significant hearing loss warranting
rehabilitation. Typically, these two options are used in patients with complete
hearing loss in one ear, such as in patients with acoustic neuromas.
With the CROS hearing aid, a microphone worn behind-the-ear is placed on the ear
with the complete hearing loss. Sound signals presented to the deaf ear are picked
up by the microphone and transmitted to a behind-the-ear (BTE) aid in the
unaffected ear. Initially, the transmission was done across a wired system involving
a headband. More recently, the signal is sent via a wireless system using radio
waves, which is more cosmetically appealing. Often, a limitation with the CROS
system is the need to wear a receiving device in the unaffected ear.
BiCROS devices, which are suitable if some hearing loss exists in the unaffected
ear, amplify sound from both sides and feed it into the ear with hearing. By
localizing the sound source and ensuring that one does not miss sounds on the deaf
side, this technology helps to restore a sense of hearing in the deaf ear (although the
result is not true bilateral hearing because all the sound is sent to only one ear).
Phonak CROS System
The new Phonak CROS is the smallest and arguably most stylish wireless
CROS/BiCROS option available. Phonak CROS consists of only two parts – a
transmitter microphone for the ear that cannot benefit from a hearing instrument,
and a receiver hearing instrument on the better hearing ear. This means sound from
your poorer hearing side is wirelessly sent to your better ear.
 A small transmitter, placed behind or inside the ear that cannot benefit from a
hearing aid, picks up sound and transfers it wirelessly to a receiver on the
normal ear. This allows hearing even when sounds come from the non-hearing
 A small transmitter, placed behind or inside the ear that cannot benefit from a
hearing aid, picks up sound and transfers it wirelessly to your ear fitted with a
hearing aid. At the same time this hearing aid amplifies sounds coming directly
to this ear. This improves hearing, understanding and communication
Accessory Options:
 Phonak ComPilot – provides easy wireless access to TVs, MP3 players and
phones to name a few.
 Phonak RemoteMic – lightweight wireless microphone combined with
ComPilot transfers partner’s voice conversation directly to the hearing aids
over a distance of up to 60 feet.
 Phonak PilotOne – focuses on the essentials when it comes to discreet control,
simplicity and user-friendly ergonomic design.
 myPilot – a remote control with a color LCD display provides users access to
a multitude of functions, including status information.
For more information go to http://www.phonak-us.com.
Currently, there are four bone conduction hearing devices available in the U.S. for
acoustic neuroma patients with unilateral hearing loss—the Cochlear™ Baha®
BP100 (Cochlear Americas), the Ponto Pro (Oticon Medical), TransEar® (Ear
Technology Corporation) and SoundBite (Sonitus Medical). The Baha BP100 and
the Ponto Pro are bone-anchored hearing devices requiring surgery. Baha hearing
devices have been available for more than 10 years in the U.S., and the BP100
replaced the Baha Divino, which is no longer manufactured. The Ponto Pro is made
by Oticon, which is a well known manufacturer of air-conduction hearing devices.
The TransEar is a bone conduction hearing device that is similar in appearance to a
conventional hearing aid, but without the need for surgery. The SoundBite is a
dental prosthetic that became available in 2012.
Bone Conduction – How It Works
Each of the four devices above transmits sound through bone conduction. Bone
conduction hearing is a natural way to hear. For example, whenever someone
brushes their teeth and hears the sound of brushing, that sound is conducted through
bone to the inner ear. Since the inner ear is encased in the bone of the skull, the
inner ear picks up sound when the skull vibrates. Sound travels through bone at
nearly the same speed it travels through air. One difference between sounds
traveling through air versus bone is that high-frequency sounds are attenuated, or
“absorbed,” when traveling through bone. Each of the bone conduction devices is
able to amplify or “boost” specific frequencies that would normally be attenuated
through bone conduction. In this way, hearing is made to sound even more natural.
Bone conduction hearing devices are an option for those patients who have no
hearing in one ear (e.g., single-sided deafness) and normal hearing in the opposite
ear. The bone conduction device is worn on the deaf side. In this way, sound is
picked up by the bone conduction device and then transmitted to the inner ear of the
other, normal hearing ear. Since the hearing device is on the deaf side, the
perception is that hearing is coming from the side with no hearing. However,
hearing in the deaf ear is not restored; the hearing loss is rehabilitated.
For those with no hearing in one ear and with a moderate hearing loss in the other
hearing ear, a special type of bone conduction hearing device is an option. This
option is known as the Cochlear Baha Intenso, a slightly larger and more powerful
device than the BP100. In this case, the patient is fitted on the deaf side with an
Intenso and the opposite side with a hearing aid. The more powerful Intenso is
necessary to adequately amplify sound to the opposite side.
Each of the bone conduction devices is helpful for two of the three hearing
difficulties that patients experience with single-sided deafness—inability to hear on
the deaf side, difficulty hearing when there is background noise, and an inability to
localize the direction of sound. Most patients that use any one of the bone
conduction hearing solutions will report that listening on the deaf side is improved
considerably, while hearing when there is background noise is improved, but the
difficulty is not eliminated.
There are some anecdotal reports of patients able to localize certain sounds with any
one of the bone conduction devices, although this is not common. Sound
localization is dependent on two, functioning ears. If the sound source is to one side
of a person, the sound is delayed as it enters the ear compared to the other side. The
brain uses this sound delay as a means to localize sound. Since current treatments
for single-sided deafness use only one functioning ear, sound localization is not
routinely reported. For those who can localize certain sounds with their bone
conduction device, sound localization may occur as a result of the slight time delay
for sound to be transmitted through the skull.
Bone-Anchored Hearing Device - Baha® - Cochlear Americas
Now in addition to the CROS and BiCROS aid options, there are several boneanchored
hearing devices that are available. After being used in Europe for several
decades, the popularity of this device has grown in the U.S. during the past 10
years, particularly as most insurance companies and Medicare cover its use.
The Baha is surgically implanted into the bone of the skull, about one inch behind
the ear canal. The implantation is performed under local or general anesthesia and
takes about one hour. The implanted portion of the device is a titanium fixture that
is surgically attached to the skull behind the deaf ear. An abutment or “snap” is
screwed into the titanium fixture. The abutment sits above the level of skin so the
sound processor can be snapped onto the abutment when the patient wishes to use
the device. This system was designed so that if the abutment is changed in the
Baha BP100
future, the abutment can be unscrewed and replaced in the physician’s office
without the need for further surgery.
Several weeks are allowed to pass after surgery to allow for bone growth (known as
osseointegration) to occur into the fixture. Osseointegration allows the fixture to be
firmly attached to the skull and results in the direct transfer of sound to the skull.
Both the fixture and abutment are MRI safe. The processor comes in different
colors to match the patient’s hair color. (Occasionally, the Baha is implanted during
acoustic neuroma surgery.)
How the Baha works:
The Baha processor works via bone conduction; the device will bypass the normal
sound conduction anatomy. (In normal hearing, sound waves go through the ear
canal, hit the ear drum, and move the three ear bones in the middle ear, which
ultimately displaces the inner ear fluid. This movement causes hair cells and nerve
fibers of the inner ear to discharge, sending a signal to the brain that allows us to
hear sound.) The Baha processor and titanium screw stimulate the inner ear
(cochlea) by conducting sound vibration through the bone. In patients with singlesided
or unilateral deafness, the Baha is placed behind the deaf ear and stimulates
the other (hearing ear’s) cochlea. New programmable sound processors offer
automatic, optimum sound quality for Baha users.
Illustration from Cochlear Americas
The BP100 has a Europin, which is a universal connection for FM and phone
adaptors. The Divino required proprietary adaptors for these applications. The
BP100 has status indicators with beeps and LEDs. There are multiple programs that
can be set for various listening situations. The programs are controlled with a single
button on top of the sound processor. Volume is controlled with up and down
buttons alongside the program button.
The BP100 has multiple channels that the audiologist can tune depending on the
thickness of the person’s skull and hearing capabilities of the opposite ear. The
Divino did not allow such fine-tuning.
For more information go to http://www.cochlear.com.
Baha device placed behind
deaf ear; reroutes sound to
better ear
Normal auditory pathway
Ponto Pro - Oticon Medical
The Pronto Pro functions in the same manner as the Baha for single-sided deafness
patients; the device reroutes sound from the deaf ear to the hearing ear via bone
conduction. Similar to the Baha device, the Ponto Pro sound processor also sits on
the skin and attaches to an abutment that is adhered to a titanium fixture in the skull.
The Ponto Pro is shaped differently than the BP100 in that the
Ponto Pro has a slight curve to its design. The program button is
on the side. Features of the Ponto Pro include multiple
programming capabilities, a self-learning volume control and a
Europin connector. In addition, the device is water-resistant. The
Ponto Pro fits on the Cochlear Baha abutment if the abutment was
placed before November 2009. In this way, someone may upgrade
from the Divino to the Ponto Pro without difficulty. Oticon
released an additional, more powerful device similar to the Intenso in the Spring of
2011. The device is digital and programmable.
For more information go to http://www.oticon.com.
TransEar® - Ear Technology Corporation
TransEar is a bone conduction hearing aid designed for individuals with unilateral
deafness and looks like a conventional behind-the-ear hearing aid but does not
require surgery.
How the TransEar works:
TransEar relies on bone conduction to transmit the sound to the better ear, without
the need for a surgically-implanted device in the skull bone. The TransEar consists
of a speech processor that rests behind the ear and is connected through a thin tube
to an ear mold that fits in the ear canal. One of the unique features of the TransEar
compared to a conventional hearing aid is that the mold of the TransEar fits very
deeply inside the ear canal. In this way, the mold can directly stimulate the bone
underneath the thin skin of the ear canal. Using bone conduction, the oscillator
conducts vibrations through the skull from the deaf side to the working cochlea on
the other side.
The current TransEar device, the 380-HF, became available
in October 2008. The 380-HF consists of a high frequency
bone vibrator, which has its peak energy at 2,100-2,300 Hz.
As a result of this peak energy, the 380-HF is able to deliver
better high frequency gain compared to its predecessor, the
270, whose peak energy was between 650-700 Hz. High
frequency gain is important, since bone will attenuate or
“slow down” sound in the region of 2,000 Hz.
Another new feature of the 380-HF compared to the 270, is that the 380-HF has a
four channel digital sound processor with two memories or programs. These two
programs are typically set for everyday listening situations and the other program
for situations involving background noise. The 380-HF also has digital feedback
reduction, which helps prevent feedback when in background noise.
For more information go to http://www.transear.com.
SoundBite™ - Sonitus Medical
SoundBite (Sonitus Medical) is the newest addition to bone-conduction hearing
devices and was FDA approved in January 2011. It is a prosthetic device that is a
non-surgical and removable hearing solution that relies on bone conduction to
imperceptibly transmit sound via the teeth for patients with single-sided deafness.
How the SoundBite works:
Nearly invisible when worn, the SoundBite system consists of two components: an
easy to insert and remove ITM (in-the-mouth) hearing device and a small BTE
(behind-the-ear) microphone unit worn on the impaired ear. No dental work or
modifications to the teeth are required.
BTE (Behind-the-Ear) Microphone Unit
 To take advantage of the natural acoustic benefits provided by the patient’s
own ear, sound in the environment is picked up by a tiny microphone placed
within an open fit dome worn in the canal of the impaired ear and connected to
the BTE by a small translucent tube. The BTE uses a digital signal processor
to process the sound and a wireless chip to transmit the signals to the ITM
hearing device, which in turn sends the imperceptible vibrations via the teeth
that are near – simultaneously to both cochlea. In this way, sound is rerouted
from the impaired ear directly to the good cochlea – bypassing the middle and
outer ear entirely – to effectively restore the perception of hearing from the
impaired ear. SoundBite Hearing System delivers sound across a broad
frequency range of 500 Hz to more than 12 kHz.
ITM (In-the-Mouth) Hearing Device
 The ITM device is custom made to fit around either the upper left or right back
teeth, does not require any alteration of the teeth and is easily inserted and
removed by the wearer. It contains electronics, a sealed, flat rechargeable
battery, wireless capability that picks up sound transmissions from the BTE and
a small actuator that converts those signals into vibrator energy. All of these
miniaturized components are hermetically sealed inside a dental grade acrylic
that has been safely used for making dental appliances for many years.
For more information go to http://www.sonitusmedical.com.
Sophono™ Alpha 1 – Sophono, Inc.
Alpha 1 is unique to traditional bone-anchored hearing systems as it is an abutmentfree
bone anchored hearing device, yet offers the same features as other boneconduction
How the Alpha 1 works:
An external processor connects to an implantable magnet (Alpha 1 M), eliminating
hair removal around an abutment placement site and complications with cleaning
this site. Another option is placement of an external processor on a soft band or
headband (Alpha 1 S). Similar to other bone-conduction devices, the Alpha 1 is
placed behind the poorer ear, stimulating the other inner ear (hearing ear’s) cochlea
by conducting sound vibration through the bone.
Cochlear Implants
Patients with acoustic neuromas and hearing loss, before or after treatment of their
tumors, often ask about cochlear implants. The cochlear implant bypasses the
damaged parts of the inner ear and stimulates the nerve endings for hearing in the
inner ear. For this reason, a cochlear implant requires an intact and functioning
hearing nerve to be successful. However, new information indicates that in certain
circumstances the hearing nerve can be stimulated, making this an option for AN
The cochlear implant is a two-part system. There is an outer or external part with a
headpiece and, most commonly, a behind-the-ear sound processor. The second part
is the internal device that is surgically implanted completely under the skin.
Cochlear implant surgery is approximately 2 hours in length, under general
anesthesia, and is a same day surgical procedure.
Cochlear implants have been around for about 25 years. Almost 200,000 of them
have been surgically implanted worldwide during that time frame.
Indications for Cochlear Implants:
Cochlear implants are indicated when the patient has significant hearing loss in both
ears. In addition, the ear to be implanted must still have the cochlear nerve and
blood supply intact. Unfortunately, this is often not the case in patients with
acoustic neuromas because of the size of the tumor or treatment with radiation
and/or surgery. However, some patients after tumor removal have some remaining
hearing, and then they lose hearing in the other ear. In these patients, placement of a
cochlear implant is a reasonable option in one or both ears.
A device related to the cochlear implant is the auditory brainstem implant (ABI).
These devices, which are typically used in patients with NF-2, can be placed in one
or both ears. The ABI does not require the presence of the cochlear nerve or blood
supply. This device requires surgical implantation at the brainstem. The ABI does
not work as well as cochlear implants (e.g., the ABI does not typically give one the
ability to talk on the telephone); however, it does allow an ability to hear
environmental sounds and assist with lip-reading.
Insurance coverage for the above devices varies. For devices that require surgery
(e.g., the Baha), some companies will cover the surgery but not the hardware. One
should determine ahead of time what will be covered. Insurance companies will
likely require a letter of medical necessity from your physician. Cochlear implants
are typically covered by insurance or Medicare only when the patient has
significant hearing loss in both ears. Medicare started to cover bone-anchored
hearing devices in 2006.
Additional options for dealing with hearing loss in patients with acoustic neuromas
include Assistive Living Devices (ALDs) (e.g., FM sound systems) that can be
found in some public places (e.g., churches, theaters, etc.). Similar to this are
products such as TV Ears, that assist AN patients with hearing in the home.
Improved hearing in everyday listening situations is of great importance for patients
with acoustic neuromas who strive to communicate with family and friends.
Fortunately, numerous hearing amplification options do exist. Conventional hearing
aids, implantable devices and bone conduction hearing systems, such as the Baha,
Ponto Pro and TransEar, enhance the patient’s ability to communicate with others.
While preservation of hearing is still a great hurdle in acoustic neuroma
management, today’s hearing rehabilitation options offer a sense of hope for
patients and improve overall quality of life.
In addition to the basic features of hearing aids, many other features are available in
modern digital hearing aids (some for convenience and ease of use) while others are
designed to improve speech understanding or listening comfort. Following is a
brief description of some of these features and the manufacturers of current hearing
aid models that provide them.
Wireless Hearing Aid Technology:
In the past two years, we have seen a lot of new “wireless” hearing aids on the
market. The term “wireless” can mean different things for different hearing aids.
Some patients use certain wireless features that others do not. Here are some
common applications for wireless hearing aids.
1. Hearing television: A hearing aid system that allows the hearing aid user to
receive the TV signal right into their hearing aids. This is done by a small box
that plugs into the TV. It like watching TV with headphones but without the
2. Hands-free Bluetooth: This allows the patient to stream wirelessly to your
cellphone via a small wireless accessory. This allows for hands-free phone use
as well as binaural hearing (hearing related to two ears).
3. One-on-one communication in noise: Some of the hearing aid manufacturers
have a “mini-microphone” that another person can speak into. The microphone
is discreet and can be clipped onto a collar or lapel. This allows that person’s
voice to be sent to the hearing aids. The result is that the voice can be heard
over and above any noise in the environment. This can be especially useful for
conversations in the car or one-on-one at a noisy restaurant.
4. Remote controls: This gives the patient control of the hearing aid via a remote
rather than pushing the buttons on the hearing aid itself. With a remote control,
you have access to hearing aid volume and can change to various programs or
settings within the hearing aid.
5. Hearing aid to hearing aid communication: Many of today’s wireless
hearing aids actually talk to each other. With directional microphone equipped
hearing aids, this can mean that the hearing aids will actually adjust themselves
to focus in on a speech signal, regardless of where it is coming from.
Adaptive Feedback Cancellation: Many of today's hearing aids have an automatic
feature that quickly detects acoustic feedback (whistling from the hearing aid
sometimes caused by placing one's hand or a phone next to the ear) and cancels it.
Automatic Gain Control-Output (AGCo): AGCo, or output compression, puts a
"ceiling" on loud sounds and can be adjusted to match the patient's threshold of
discomfort by maintaining sounds below this level.
Automatic Gain Control-Input (AGCi): AGCi, or input compression, also called
wide dynamic range compression (WDRC), compresses speech or other incoming
sound signals to fit into the reduced range of the hearing aid user, which provides
more gain for soft sounds than for average and more gain for average sounds than
for loud. With this feature, many hearing aid users have little need for a volume
Multiple Channels: The majority of today's hearing aids have multiple channels.
Each channel represents a portion of the frequency range important for
understanding speech. Gain and compression can be programmed differently in
each channel to reflect changes in the patient's hearing across frequencies.
Digital Noise Reduction: This feature allows the hearing aid to analyze an
incoming signal and differentiate speech from a broadband noise (which presents
simultaneously in several channels) and reducing gain if a signal is believed to be
noise in a given channel.
Directional Microphone Technology: Using special microphones or phase
cancellation signal processing, it is possible to configure a hearing aid so that
sounds from the side and back of the user are amplified less than sounds originating
from the front. Hearing aid users have reported this especially useful when
background noise originates from behind the listener, the talker is in front of the
listener, the listener is close to the talker and the room has low reverberation.
Multiple Memories: A memory is a location to store settings designed for a
particular listening situation (for example listening in quiet, listening in noise, or for
listening on the telephone). It is common for hearing aids to come with two or three
memories that can be switched by using a button. In some digital hearing aids, it
happens automatically.
Telecoils: The telecoil is a small component in the aid that picks up signals from a
loop system or hearing aid compatible telephone. A loop system helps to hear sound
from a television, stereo, or radio, or can be set up with a microphone to help hear
conversations in noisy places or even in the theater. Telecoils are not available in
some smaller models due to space limitations.
Sound Recover: Sound recover technology, from Phonak, compresses and shifts
high frequency information into an area of greater audibility for the patient,
resulting in increased audibility of high frequency sounds.
Table 2: Manufacturers and Models
Manufacturer* Models*
Phonak Audeo S, Virto, Naida S, Bolero
Oticon Agil Pro, Acto, Chili
Starkey Wi Series, 3 Series, Tour, Ignite
Widex Clear, Mind, Menu
GN Resound Verso, Alera, Vea, Essence
Siemens Life, Pure, Motion, Nitro
* Note: Additional manufacturers and models of hearing aids are available.
An audiologist will assist the patient in selecting the most appropriate hearing
Written by:
Ravi N. Samy, M.D., F.A.C.S. (University of Cincinnati / Cincinnati Children's
Hospital Medical Center)
Lisa Houston, Au.D. (University of Cincinnati)
Julie Honaker, Ph.D. (University of Nebraska-Lincoln)
Robert A. Battista, M.D., (Northwestern University Medical School / Ear Institute
of Chicago)
Last edited by Subri on Mon Jun 27, 2016 2:25 pm, edited 1 time in total.
Reason: as suggested
:) SUBRI IGAN forum Moderator and post resection of left acoustic neuroma with permanent deafness left ear
Post Reply